Installing Telguard TG7 - Introductory Class 101
Posted: Fri Jan 06, 2017 7:29 pm
Basics and Advance installation of the TG7
https://www.telguardonline.com/
http://www.thealarmtech.com/manuals/Tel ... nstall.pdf
-------------------------------------------------------
**** important ****
Sending Signals from Telguard to your CS via an internet connection:
You may have noticed that the signals sent from a Telguard to your CS are delay by sometimes 20 minutes,
THIS IS A JOKE and when I say joke I mean a complete embarrassment.
If your CS has a receiver that can get signals from Telguard via the internet the signal is received by your CS in seconds.
CID is the only format that can use an internet connection
4/2, SIA can only dial into your receiver.
-------------------------------------------------------
Pulse or Rotary
Most if not all phone lines do NOT work on ROTARY anymore.
when you have a control that fails to get out vs pulse a few times it may go to rotary and stay there, ever if the lines restore the control will not.
I have seen these a few times with the v32fb panel.
Good news the TG7 will work with Rotary
-------------------------------------------------------
10 Digit dial only
When programming FACP make sure the Receiver phone numbers are 10 Digits or the TG7 will not work.
Note: 555-5555 will not work.
-------------------------------------------------------
The TG7 is active when the top green LED is on.
The first Signal that is sent from your FACP will activate the TG7.
Note: The first signal is not sent to the CS, only to Telguard
-------------------------------------------------------
RJ45 Splitter for Connecting both primary and secondary phone jacks to Telguard's one jack.
https://cdn.adiglobal.us/CatalogImages/ ... SPLT-1.jpg
Fire-Lite Model #: IPSPLT
* great little device
PROGRAMMING for 4/2 format - supv the comm fail
-------------------------------------------------------
Link Supervision
Supervision Restoral Code - 1414
Supervision Fail Code - 1515
when the telguard link fails a "FF" will go to your CS
when the telguard link restores a "EE" will go to your CS
let your CS know the fail/restore codes
PROGRAMMING
-------------------------------------------------------
Registering a new TG7
Tab: Subscriber & Units -> Register Subscriber
-------------------------------------------------------
Installing Telguard TG7 as "Mode of Operation" Cellular only
Tab: Link Supervision - Sole Path Fire (60 minutes) NFPA 2013
Tab: Link Supervision - Sole Path Fire (5 minutes) NFPA 2010
Yellow LED 5 Flashing - Link supervision Enable (2 flashes every 6 seconds)
Note: if LED 5 is not flashing Link supv is not enable.
LEDS for Cellular only : top green on, bottom red power on and LED 5 flashing.
-------------------------------------------------------
Setting the Account and Receiver phone numbers
Tab: Central Station Info -> Alarm Panel CC
The TG7 will use the FACP's account and receiver numbers.
Tab: Central Station Info -> TCC (Telular Comm Center)
The TG7 will use the account and receiver numbers enter in the below fields.
Note: only use when "Mode of Operation" is Cellular only.
When TG7 uses phone lines it sends FACP's account and receiver numbers.
https://www.telguardonline.com/
http://www.thealarmtech.com/manuals/Tel ... nstall.pdf
-------------------------------------------------------
**** important ****
Sending Signals from Telguard to your CS via an internet connection:
You may have noticed that the signals sent from a Telguard to your CS are delay by sometimes 20 minutes,
THIS IS A JOKE and when I say joke I mean a complete embarrassment.
If your CS has a receiver that can get signals from Telguard via the internet the signal is received by your CS in seconds.
CID is the only format that can use an internet connection
4/2, SIA can only dial into your receiver.
-------------------------------------------------------
Pulse or Rotary
Most if not all phone lines do NOT work on ROTARY anymore.
when you have a control that fails to get out vs pulse a few times it may go to rotary and stay there, ever if the lines restore the control will not.
I have seen these a few times with the v32fb panel.
Good news the TG7 will work with Rotary
-------------------------------------------------------
10 Digit dial only
When programming FACP make sure the Receiver phone numbers are 10 Digits or the TG7 will not work.
Note: 555-5555 will not work.
-------------------------------------------------------
The TG7 is active when the top green LED is on.
The first Signal that is sent from your FACP will activate the TG7.
Note: The first signal is not sent to the CS, only to Telguard
-------------------------------------------------------
RJ45 Splitter for Connecting both primary and secondary phone jacks to Telguard's one jack.
https://cdn.adiglobal.us/CatalogImages/ ... SPLT-1.jpg
Fire-Lite Model #: IPSPLT
* great little device
PROGRAMMING for 4/2 format - supv the comm fail
-------------------------------------------------------
Link Supervision
Supervision Restoral Code - 1414
Supervision Fail Code - 1515
when the telguard link fails a "FF" will go to your CS
when the telguard link restores a "EE" will go to your CS
let your CS know the fail/restore codes
PROGRAMMING
-------------------------------------------------------
Registering a new TG7
Tab: Subscriber & Units -> Register Subscriber
-------------------------------------------------------
Installing Telguard TG7 as "Mode of Operation" Cellular only
Tab: Link Supervision - Sole Path Fire (60 minutes) NFPA 2013
Tab: Link Supervision - Sole Path Fire (5 minutes) NFPA 2010
Yellow LED 5 Flashing - Link supervision Enable (2 flashes every 6 seconds)
Note: if LED 5 is not flashing Link supv is not enable.
LEDS for Cellular only : top green on, bottom red power on and LED 5 flashing.
-------------------------------------------------------
Setting the Account and Receiver phone numbers
Tab: Central Station Info -> Alarm Panel CC
The TG7 will use the FACP's account and receiver numbers.
Tab: Central Station Info -> TCC (Telular Comm Center)
The TG7 will use the account and receiver numbers enter in the below fields.
Note: only use when "Mode of Operation" is Cellular only.
When TG7 uses phone lines it sends FACP's account and receiver numbers.