TheAlarmTech.com

for sample:

name for switch: "CAB_OP1_SW01_M1EVAC" the * is comodin name for all cases
name for amplificator: "CAB1_AMP1" and 'ch_Evac_01_08' is the evacuation audio channel
name for led button: "CAB1_OP1_LED1_M1EVAC"

///////////////////////////////// ruler for switch //////////////////////////////////////////////////////
[PULSADOR EVAC NIVEL M1,M2,M3]
SW 'CAB1_OP*_SW*_M<N:1-3>EVAC' :
+Ampon 'CAB1_AMP*' TO 'ch_Evac_01_08', {Activa canal de evacuacion para el amplificador 3-ZA20 etiquetado como CAB1_AMP*: el backup y el principal}
-Ampoff 'CAB1_AMP*' TO 'ch_Evac_01_08',
+MSGON 'Default_evac_01_08' TO 'ch_Evac_01_08', {Activa mensaje evacuacion(default) por voz en canal de evacuacion}
-MSGoff 'Default_evac_01_08' TO 'ch_Evac_01_08',
On AUD 'M<N>_CH1_AMP*', {Activa salida canal1 de modulo AA50 *_*_SPK* configurado como audible, en nivel M1}
On AUD 'M<N>_*_CH1_SPK*', {Activa salida de modulo SIGA-CC1/CC2 *_*_SPK* configurado como audible, en nivel M1}
steady 'CAB1_OP*_LED*_M<N>EVAC';

//////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

animeshhazra wrote:I have 7 yrs experience in Siemens FDA System doing commissioning. I also did many project in EST3 but only FDA there. I did networking, graphics also in EST3. But I did not commissioned any panel with Voice. Here I stuck in a site with 1 SDDC1, 1 ZA40-B, 3-12SG, 1 ASU-FT unit. In PA there is 2 zone, talkback 1 zone. So for that case (2+1) CC1 has set up. I also mapped loops and get all the devices. Can anyone help me to write rules for PA, Talkback and for LED switches(3-12SG)? Thanks in advance.

Animeshhazra, Are you the only programmer in your company?

animeshhazra wrote:I have 7 yrs experience in Siemens FDA System doing commissioning. I also did many project in EST3 but only FDA there. I did networking, graphics also in EST3. But I did not commissioned any panel with Voice. Here I stuck in a site with 1 SDDC1, 1 ZA40-B, 3-12SG, 1 ASU-FT unit. In PA there is 2 zone, talkback 1 zone. So for that case (2+1) CC1 has set up. I also mapped loops and get all the devices. Can anyone help me to write rules for PA, Talkback and for LED switches(3-12SG)? Thanks in advance.

Read and Read hardware and programming manuals Edwards Est3.. and puntuals questions here..

I have 7 yrs experience in Siemens FDA System doing commissioning. I also did many project in EST3 but only FDA there. I did networking, graphics also in EST3. But I did not commissioned any panel with Voice. Here I stuck in a site with 1 SDDC1, 1 ZA40-B, 3-12SG, 1 ASU-FT unit. In PA there is 2 zone, talkback 1 zone. So for that case (2+1) CC1 has set up. I also mapped loops and get all the devices. Can anyone help me to write rules for PA, Talkback and for LED switches(3-12SG)? Thanks in advance.